Gw-instek GDM-8261A Remote Viewer(DMM-Viewer) Guide Manual de usuario

DMM Viewer GDM-8261(A) Remote Viewer Guide GW INSTEK PART NO. ISO-9001 CERTIFIED MANUFACTURER

GDM-8261(A) Remote Viewer Guide 10 Installation Two items, the USB driver and DMM Viewer Software need to be installed onto the PC in order to run t

SETUP 11 3. The installation wizard will start up. Follow the directions of the installation wizard. When choosing an install location it is re

GDM-8261(A) Remote Viewer Guide 12 Uninstallation Follow the procedures described in this section when the viewer software or the USB driver needs t

SETUP 13 3. Select Delete the driver software for this device, then press the OK button. The driver will uninstall automatically. Uninstalling

GDM-8261(A) Remote Viewer Guide 14 Configuration 1. Configure the PC 1. To make sure the DMM is recognized by the PC, open the Device Manager (St

SETUP 15 Success Fail 4. Click on OK to save and leave the Settings screen. 5. Move on to Measurement (page 16).

GDM-8261(A) Remote Viewer Guide 16 MEASUREMENT 1. Establish remote connection Follow the procedures for connection and configuration on page 7 and

MEASUREMENT 17 Data field 4. Stop measurement Click on the START button again to stop the measurement. The button color changes from red to blac

GDM-8261(A) Remote Viewer Guide 18 Note If Test Speed is set to 16.667ms or 33.333ms, the test value will be directly written to a log file and will

MEASUREMENT 19 View the measurement mode To check the measurement mode of the DMM, click on the Show Mode button in the command plane. The mode a

This manual contains proprietary information, which is protected by copyrights. All rights are reserved. No part of this manual may be photocopied

GDM-8261(A) Remote Viewer Guide 20 PLOT GRAPH/ SAVE To be able to plot data, it must first be saved. Once data is retrieved, the measurement data ca

PLOT GRAPH/ SAVE 21 Note The log file will immediately start to save after the OK button has been pressed. Load data 1. Click on the Load button

GDM-8261(A) Remote Viewer Guide 22 Plotting the data 1. First make sure you have saved a session and loaded data to be able to plot data. 2. Pres

PLOT GRAPH/ SAVE 23 Changing the plot point range 1. The start and end points of the plot can be changed by manipulating the Set Range panel.

GDM-8261(A) Remote Viewer Guide 24 2. Left click and hold the top left most corner of the area you want to select 3. Drag down to the bottom

SCANNER FUNCTION 25 SCANNER FUNCTION 1. Establish remote connection Follow the procedures for connection and configuration on page 7 and page 14.

GDM-8261(A) Remote Viewer Guide 26 4. Chanel selection configuration 1. Check the ON: checkbox above a channel to activate that channel in the scan

SCANNER FUNCTION 27 2. To unselect Auto Range, uncheck the checkbox or click the Auto All Clear button 7. Scan configuration Scan count Set the

GDM-8261(A) Remote Viewer Guide 28 8. Run a scan After all the settings have been configured a scan can be started. Click SCAN to scan all the acti

SCANNER FUNCTION 29 12. Load settings 1. Click the ScanBox Setting button at the top of the screen. 2. Select Load ScanBox Status(S). 3. A po

Table of Contents 3 TABLE OF CONTENTS INTRODUCTION ...

GDM-8261(A) Remote Viewer Guide 30 FIRMWARE/ VERSION This section describes how to access the firmware file and the Firmware Update Manual included

FIRMWARE/ VERSION 31 View Software Version You may need to check the version of the software to see if you have the latest version. 1. Start

GDM-8261(A) Remote Viewer Guide 4 INTRODUCTION This manual is suitable for both GDM-8261 and GDM-8261A. The GDM-8261(A) Remote Viewer Guide is inten

INTRODUCTION 5 CD-ROM Overview The CD-ROM contains all the items needed to install and run the software, plus more. Main menu Inserting the CD-RO

GDM-8261(A) Remote Viewer Guide 6 User Manual menu This menu loads the DMM User Manual. Firmware Update Software menu This menu accesses a copy of

SETUP 7 SETUP Connection When using DMM Viewer in Conjunction with the GDM-8261(A), use the following instructions to set the DMM to RS232 or USB

GDM-8261(A) Remote Viewer Guide 8 4. The USB ON or OFF selection appears. Press the Up or Down key to turn on. 5. Press the ENTER key to conf

SETUP 9 Baud rate: 9600, 19200, 38400, 57600, 115200, 230400 5. Press the ENTER key to confirm the RS232 baud rate. 6. Press the EXT key to