Gw-instek APS-1102 Control Software User Manual Manual de usuario Pagina 85
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APS-1102A Control Software User Manual
72
7.10.4 Created Arbitrary Waveforms Examples
As an example of operations, we will create a waveform of sine wave with noise superimposed.
Step 1:
Display [New Arbitrary Waveform Editing Panel].
In its initial state, a sine wave is selected.
Change the value on the right side of [Amplitude] from [65534] to [50000] to make the
amplitude smaller.
Click All-Page OK button to return to waveform display screen.
Step 2:
Click Operate button on Select Item Panel.
You can also click [Tool] - [Operate] to obtain the same result.
Select Item Panel is changed to [Operate Panel].
Step 3:
Click the Created Waveform button.
Step 4:
Select [Waveform] combo box, and then click [Noise] in the list displayed.
Change the value on the right side of [Amplitude] from [65534] to [15000].
Return to [Operate Panel] by clicking Page OK button.
In this stage, the result of the addition is displayed in the [Operation Result] field.
Step 5:
Click OK button to return to waveform display section.
This produces a waveform of a sine wave with noise superimposed.
Description 1:
Subtraction, multiplication, and division are also available as well as addition which was
shown in this example.
Description 2:
You can operate for only a part of a waveform by selecting that part of the waveform
using A and B markers in the waveform display screen beforehand.
Description 3:
In this example, the waveform created on the [Arbitrary Waveform Editing Panel] is used
for operation.
In step 3, the contents in "clip board" can be used for operation by clicking Clip Board
button.
Description 4:
When executing multiplication, it is convenient to set the unit of the vertical axis as ±1 of
the user-defined unit.
This makes the result of the multiplication between full scale values to a full scale value
also.
- REVISION 1.0 December 2013 1
- ISO-9001 CERTIFIED 1
- MANUFACTURER 1
- Preface 4
- Safety Precautions 5
- Disclaimer 6
- About Copyrights 6
- Contact Us 6
- Contents 8
- Figures and Tables 12
- Outline 14
- 1.1 Overview 15
- 1.2 Software Configuration 16
- Installation 17
- 2.1 System Requirements 18
- 2.2 Installation Procedure 19
- 2 Installation 20
- Control Software Operation 21
- 3.1 Start and Exit 22
- 3.5 Common Display Section 25
- 3.6 System Setting 26
- 3.7 Error Message 26
- Basic Controller 27
- 4.2.1 Menu Bar 29
- 4.2.2 Tool Bar 29
- 4.2.4 Basic Setting 30
- 4.2.5 Output Setting 31
- 4.2.6 Limiter Setting 32
- 4.2.7 Operation Bar 32
- OUTPUT Off 32
- OUTPUT On 32
- 4.3.1 Save As 33
- 4.3.2 Save 33
- 4.3.3 File Reading 33
- CAUTION 33
- 4.4 Memory 34
- 4.5 Status 35
- 4.6 Logging 36
- Sequence 37
- 5 Sequence 38
- 5.2.2 Tool Bar 40
- 5.2.3 Basic Setting 40
- 5.2.4 Step Arrangement 41
- Display disabled 44
- Display enabled 44
- Change the operation type 45
- 5.3 Sequence Setting File 46
- 5.4 Control 47
- 5.4.5 Output On 48
- 5.4.6 Output Off 48
- 5.4.7 Switch Execution Mode 48
- Measurements Logging 49
- 6 Measurements Logging 50
- 6.3.1 Menu Bar 51
- 6.3.2 Tool Bar 51
- 6.3.4 Logging Conditions 52
- 6.4 Log Display Section 53
- 6.5 Measurements Log File 53
- Arbitrary Waveform Editing 54
- 7.1 Overview 55
- 7.4.1 Menu Bar 58
- Select Item Panel 59
- 7.5.1 Waveform Display Area 60
- 7.5.2 Display Magnification 60
- 7.5.3 Markers 61
- 7.5.4 Waveform Manipulation 62
- 7.5.6 Grid 64
- 7.6 File Operation 65
- 7.7 Printing Waveforms 67
- 7.8.1 Range/Page 69
- 7.8.2 Select a Waveform 69
- 7.8.3 Parameter Setting 70
- 7.8.7 Print 77
- 7.9 Interpolate 78
- 7.9.1 Control Point Setting 79
- 7.9.2 Execute Interpolation 80
- 7.10 Operation 83
- 7.10.1 Types of Operation 84
- 7.10.3 Operation Execution 84
- 7.11 Compress/Expand 86
- button or Expand with 89
- button 89
- 7.12 System Setting 90
- 7.13 Memory 91
- Maintenance 93
- 8.1 CD-ROM Management 94
- 8.2 Replace Damaged CD-ROM 94
- 8.3 Check Version 94
Relacionado con productos y manuales para Equipo Gw-instek APS-1102 Control Software User Manual
Equipo Gw-instek PCS-1000 Manual de usuario
(93 paginas)
(93 paginas)
Equipo Gw-instek GPD-4303S Manual de usuario
(59 paginas)
(59 paginas)
Equipo Gw-instek APS-1102A User Manual Manual de usuario
(285 paginas)
(285 paginas)
Equipo Gw-instek PPH-1503 Manual de usuario
(137 paginas)
(137 paginas)
Equipo Gw-instek LCR-914 Manual de usuario
(28 paginas)
(28 paginas)
Equipo Gw-instek LCR-800 Series Manual de usuario
(72 paginas)
(72 paginas)
Equipo Gw-instek GPM-8212 Manual de usuario
(14 paginas)
(14 paginas)
Equipo Gw-instek GFC-8010H Manual de usuario
(10 paginas)
(10 paginas)
Equipo Gw-instek GFC-8131H Manual de usuario
(7 paginas)
(7 paginas)
Equipo Gw-instek GLC-9000 User Manual Manual de usuario
(187 paginas)
(187 paginas)
Equipo Gw-instek LCR-8000G Series Manual de usuario
(72 paginas)
(72 paginas)
Equipo Gw-instek GVT-427B Manual de usuario
(9 paginas)
(9 paginas)
Equipo Gw-instek GAD-201G Manual de usuario
(8 paginas)
(8 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales