Gw-instek PEL-2000 Series Programming User Manual Manual de usuario Pagina 164
- Pagina / 170
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PEL-2000 Programming Manual
164
Channel Status
Description
Each channel has a dedicated Channel Status
Register group. These registers show if any errors
or faults have occurred to a specific channel.
The Channel Status Register group consists of: the
Condition, EVENT and ENABLE registers as well
as PTR/NTR (positive and negative transition)
filters.
Channel Status Registers
8
3
4
2
2
1
1
0
RV OP OV OC
7-15
0
Bit weight
Bit Position
Condition
RV OP OV OC0PTR/NTR
RV OP OV OC0EVENT
RV OP OV OC0ENABLE
UVP G/N OT
UVP G/N OT
UVP G/N OT
UVP G/N OT
6 5 4
64 32 16
Protection Bits
OC
If an over current condition occurs the
OC bit (bit 0) is set. The OC bit can only
be cleared with
the :LOAD:PROTection:CLEar command.
OV
If an over voltage condition occurs the
OV bit (bit 1) is set. The OV bit can only
be cleared with
the :LOAD:PROTection:CLEar command.
OP
If an over power condition occurs the OP
bit (bit 2) is set. The OP bit can only be
cleared with
the :LOAD:PROTection:CLEar command.
RV
If a reverse voltage condition occurs the
RV bit (bit 3) is set. The RV bit is
automatically cleared after the reverse
voltage is removed.
OT
When the internal temperature exceeds
85˚C the OT bit will be set. The OT bit is
automatically cleared after the
temperature goes below 85˚C.
- PEL-2000 Series 1
- PROGRAMMING MANUAL 1
- Table of Contents 3
- INTERFACE OVERVIEW 5
- Interface 6
- GPIB Interface Configuration 11
- COMMAND OVERVIEW 13
- FETCh:VOLTage? 14
- COMMAND OVERVIEW 23
- Global 23
- COMMAND DETAILS 24
- COMMAND DETAILS 25
- Common commands 26
- Manufacturer 28
- Abort Subsystem 32
- Channel Subsystem 33
- :CHANnel:ACTive 34
- :CHANnel:SYNCon 34
- :CHANnel:SYNCon:ALL 35
- :CHANnel:ID? 35
- :CHANnel:DISPlay 35
- :CHANnel:MEMo 36
- CONFIGURE Subsystem 38
- :CONFigure:VOLTage:RANGe 39
- :CONFigure:VOLTage:LATch 40
- :CONFigure:AUTO:LOAD 40
- :CONFigure:AUTO:MODE 41
- :CONFigure:SOUND 41
- :CONFigure:SAVE 42
- :CONFigure:LOAD 42
- :CONFigure:REMote 42
- :CONF:PROT:CURR:STAT 1 43
- :CONF:PROT:CURR:STAT? 43
- :CONFigure:RESPonse 48
- :CONFigure:RESEt 49
- :CONFigure:GROup:UNITs 49
- :CONFigure:GROup:MODE 50
- Utility Subsystem 51
- :UTILity:AUTO:MODE 52
- :UTILity:SOUNd 52
- :UTILity:REMote 53
- :UTILity:REMote:MODE 53
- :UTILity:IDENtify 55
- :UTILity:FRAMe 55
- Current Subsystem 56
- :CURRent:STATic:L1/L2 57
- :CURRent:STATic:RISE/FALL 58
- :CURR:STAT:LOW:RISE .001 60
- :CURRent:DYNamic:L1/L2 62
- :CURRent:DYNamic:RISE/FALL 63
- :CURRent:DYNamic:T1/T2 64
- :CURRent:DYNamic:LOW:L1/L2 65
- :CURRent:DYNamic:LOW:T1/T2 67
- :CURRent:DYNamic:HIGH:L1/L2 67
- :CURRent:DYNamic:HIGH:T1/T2 69
- FETCH Subsystem 71
- :FETCh:POWer? 72
- :FETCh:STATus? 72
- :FETCh:ALLVoltage? 72
- :FETCh:ALLCurrent? 73
- :FETCh:ALLPower? 73
- LOAD Subsystem 75
- :LOAD:SHORt:KEY 76
- :LOAD:PROTection? 76
- :LOAD:PROTection:CLEar 77
- :LOAD:TIME? 77
- :LOAD:DELay 78
- :LOAD:TYPE 78
- Measure Subsystem 80
- :MEASure:POWer? 81
- :MEASure:INPut 81
- :MEASure:SCAN 82
- :MEASure:ALLVoltage? 82
- :MEASure:ALLCurrent? 83
- :MEASure:ALLPower? 83
- MODE Subsystem 85
- OCP Test Automation Commands 87
- :OCP:CHANnel:RANGe 88
- :OCP:CHANnel:STARt 88
- :OCP:CHANnel:END 89
- :OCP:CHANnel:STEP:CURRent 89
- :OCP:CHANnel:LAST 90
- :OCP:CHANnel:STEP:TIME 90
- :OCP:CHANnel:DELay 91
- :OCP:CHANnel:TRIGger 91
- :OCP:CHANnel:ACTive 92
- :OCP:STATus? 92
- :OCP:SAVE 93
- :OCP:RESult? 93
- :OCP:RUN 93
- Program Subsystem 94
- :PROGram:SEQuence 95
- :PROGram:MEMory 95
- (BIT WEIGHT) 96
- :PROGram:SEQuence:SHORt:TIME 97
- :PROGram:SEQuence:MODE 97
- :PROGram:ACTive 98
- :PROGram:CHAin 99
- :PROGram:ONTime 99
- :PROGram:OFFTime 100
- :PROGram:RUN 101
- :PROGram:SAVE 101
- :PROGram:PFTime 101
- :PROGram:CHAin:STARt 102
- Resistance Subsystem 103
- :RESistance:STATic:RECall 105
- RUN Subsystem 115
- SHOW Subsystem 116
- SPECIFICATION Subsystem 118
- :SPECification:TEST: 121
- STATUS Subsystem 122
- :STATus:CHANnel:ENABle 123
- :STATus:CHANnel:EVENt? 123
- :STATus:CHANnel:NTRansition/ 124
- PTRansition 124
- :STATus:CSUMmary:ENABle 125
- :STATus:CSUMmary:EVENt? 126
- :STATus:QUEStionable:ENABle 127
- :STATus:PREset 129
- Voltage Subsystem 130
- :VOLTage:RECall 131
- :VOLTage:AVALue/BVALue 131
- :VOLTage:CURRent 132
- :VOLTage:MODE 133
- Power Subsystem 135
- :POWer:CURRent 136
- :POWer:RECall 137
- :POWer:LOW:AVALue/BVALue 137
- :POWer:LOW:CURRent 138
- :POWer:HIGH:AVALue/BVALue 139
- :POWer:HIGH:CURRent 140
- SYSTEM Subsystem 141
- :SYSTem:SETup 142
- Memory Subsystem 143
- :MEMory:SAVE:ALLPreset 144
- :MEMory:SAVE:SETup 144
- :MEMory:RECall:PREset 144
- :MEMory:RECall:PROGram 145
- :MEMory:RECall:ALLPreset 145
- :MEMory:RECall:SETup 145
- :MEMory:FILE:PRESet 146
- :MEMory:FILE:PROGram 146
- :MEMory:FILE:SETup 147
- :MEMory:FILE:SEQuence 147
- SEQuence Subsystem 149
- :SEQuence:END 150
- :SEQuence:POINt:RESistance 150
- :SEQuence:POINt:CURRent 151
- :SEQuence:POINt:RISE/FALL 151
- :SEQuence:REPeat 153
- :SEQuence:END:LOAD 153
- :SEQuence:VOLTage:RANGe 154
- :SEQuence:LOOP:STARt 155
- :SEQuence:CHANnel:TIME 155
- :SEQuence:RUN 156
- :SEQuence:SAVE 156
- :SEQuence:TRIGger:IN 156
- :SEQuence:TRIGger:OUT 157
- :SEQuence:TRIGger:IN:CHANnel 157
- GLOBal Subsystem 159
- Command Error Codes 161
- STATUS REGISTERS 162
- STATUS REGISTERS 163
- Channel Status 164
- Channel Summary 165
- Questionable Status 166
- Output Queue 167
- Data inData out 167
- Standard Event Status 168
- Status Byte Register 169
- Service Request Register 170
Relacionado con productos y manuales para Equipo Gw-instek PEL-2000 Series Programming User Manual
Equipo Gw-instek APS-1102 User Manual Manual de usuario
(265 paginas)
(265 paginas)
Equipo Gw-instek PCS-1000 Manual de usuario
(93 paginas)
(93 paginas)
Equipo Gw-instek GPD-4303S Manual de usuario
(59 paginas)
(59 paginas)
Equipo Gw-instek APS-1102A User Manual Manual de usuario
(285 paginas)
(285 paginas)
Equipo Gw-instek PPH-1503 Manual de usuario
(137 paginas)
(137 paginas)
Equipo Gw-instek LCR-914 Manual de usuario
(28 paginas)
(28 paginas)
Equipo Gw-instek LCR-800 Series Manual de usuario
(72 paginas)
(72 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales