Gw-instek PEL-3000 Series Programming Manual Manual de usuario Pagina 43
- Pagina / 174
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
COMMNAND OVERVIEW
41
Configure Subsystem Commands
[:CONFigure]:OCP .............................................................. 41
[:CONFigure]:OPP ............................................................... 42
[:CONFigure]:UVP............................................................... 43
[:CONFigure]:OVP .............................................................. 43
[:CONFigure]:SSTart ............................................................ 44
[:CONFigure]:VON ............................................................. 45
[:CONFigure]:VDELay ........................................................ 45
:CONFigure:RESPonse ....................................................... 46
[:CONFigure]:CNTime ........................................................ 46
[:CONFigure]:COTime ........................................................ 47
[:CONFigure]:CRUNit ......................................................... 48
:CONFigure:DYNamic ........................................................ 48
:CONFigure:MEMory .......................................................... 49
:CONFigure:SHORt............................................................. 49
[:CONFigure]:GNG:SPECtest ........................................... 50
[:CONFigure]:GNG:DTIMe .............................................. 50
[:CONFigure]:GNG:MODE .............................................. 51
[:CONFigure]:GNG[:PASS] ................................................ 51
[:CONFigure]:GNG:H ........................................................ 52
[:CONFigure]:GNG:L ......................................................... 52
[:CONFigure]:GNG:C ......................................................... 53
[:CONFigure]:OCP
Set
Query
Description
Sets or queries the OCP trip settings. The OCP
limit can be set to a specific value or the trip setting
can be set to either limit the current or to turn the
load off.
Syntax
[:CONFigure]:OCP {<NRf>[ A ] | MINimum |
MAXimum | LIMit | LOFF }
Query Syntax
[:CONFigure]:OCP?
Parameter
<NRf>[A]
Current limit value.
- DC Electronic Load 1
- Table of Contents 3
- INTERFACE OVERVIEW 4
- Front Panel Overview 5
- Rear Panel Overview 6
- Interface Configuration 7
- Configure GPIB Interface 8
- 1 2 3 4 5 9
- GPIB Function Check 15
- INTERFACE OVERVIEW 17
- COMMNAND OVERVIEW 18
- :CURRent:Set 21
- Command List 23
- :CURRent[:VA]:TRIGgered 37
- :RESistance[:VA]:TRIGgered 37
- Example 38
- :RESistance:TRIGgered MAX 38
- :INPut:MODE 40
- :MEASure:ETIMe? 42
- Configure Subsystem Commands 43
- [:CONFigure]:OCP 43
- [:CONFigure]:OPP 44
- [:CONFigure]:SSTart 46
- [:CONFigure]:COTime 49
- [:CONFigure]:GNG:C 55
- Parallel Commands 56
- [:CONFigure]:PARallel 56
- Step Resolution Commands 58
- [:CONFigure]:STEP:CCH 58
- [:CONFigure]:STEP:CC 60
- [:CONFigure]:STEP:CRH 60
- [:CONFigure]:STEP:CRM 61
- [:CONFigure]:STEP:CRL 62
- [:CONFigure]:STEP:CR 62
- [:CONFigure]:STEP:CV 64
- [:CONFigure]:STEP:CPH 64
- [:CONFigure]:STEP:CP 66
- [:MODE]:DYNamic 71
- Current Subsystem Commands 72
- :CURRent[:VA] 72
- :CURRent:SET 75
- :CURRent:T2 78
- :RESistance[:VA] 81
- :RESistance:L1 83
- :RESistance:LEVel 85
- :RESistance:T1 87
- :RESistance:DUTY 89
- Power Subsystem Commands 93
- :POWer[:VA] 93
- :POWer:LEVel 96
- :POWer:FREQuency 98
- :POWer:DUTY 99
- Function Commands 100
- :PROGram:STATe 101
- :PROGram 102
- :PROGram[:RECall]:DEFault 103
- :PROGram:STARt 103
- [:PROGram]:CHAin:P2P 109
- :PROGram:SAVE 110
- :NSEQuence:STATe 110
- :NSEQuence 111
- :NSEQuence:STARt 112
- :NSEQuence:EDIT 117
- :NSEQuence:EDIT:POINt 118
- :FSEQuence 120
- :FSEQuence:MEMO 121
- :FSEQuence:EDIT:POINt 126
- :FSEQuence:SAVE 128
- :UTILity:LOAD:MODE 130
- :UTILity:LOAD:RANGe 131
- SCPI Register Commands 142
- :SYSTem:ERRor? 142
- :STATus:PRESet 143
- :STATus:CSUMmary:PTRansition 151
- Status Registers 153
- CSummary Status Registers 155
- Questionable Status Register 156
- Operation Status Registers 157
- Status Byte Register 160
- Service Request Register 161
- Error Messages 162
Relacionado con productos y manuales para Equipo Gw-instek PEL-3000 Series Programming Manual
Equipo Gw-instek APS-1102 User Manual Manual de usuario
(265 paginas)
(265 paginas)
Equipo Gw-instek PCS-1000 Manual de usuario
(93 paginas)
(93 paginas)
Equipo Gw-instek GPD-4303S Manual de usuario
(59 paginas)
(59 paginas)
Equipo Gw-instek APS-1102A User Manual Manual de usuario
(285 paginas)
(285 paginas)
Equipo Gw-instek PPH-1503 Manual de usuario
(137 paginas)
(137 paginas)
Equipo Gw-instek LCR-914 Manual de usuario
(28 paginas)
(28 paginas)
Equipo Gw-instek LCR-800 Series Manual de usuario
(72 paginas)
(72 paginas)
Equipo Gw-instek GPM-8212 Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales