Gw-instek PEL-3000 Series Programming Manual Manual de usuario Pagina 72
- Pagina / 174
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PEL-3000 Programming Manual
70
Current Subsystem Commands
:CURRent[:VA] ..................................................................... 70
:CURRent:VB ........................................................................ 71
:CURRent:SRATe ................................................................. 71
:CURRent:L1 ......................................................................... 72
:CURRent:L2 ......................................................................... 72
:CURRent:SET ...................................................................... 73
:CURRent:LEVel .................................................................. 74
:CURRent:RISE .................................................................... 74
:CURRent:FALL ................................................................... 75
:CURRent:T1 ......................................................................... 75
:CURRent:T2 ......................................................................... 76
:CURRent:FREQuency ........................................................ 77
:CURRent:DUTY ................................................................. 77
:CURRent[:VA]
Set
Query
Description
Sets or queries the CC mode “A Value” (static
mode) current. This command is applicable to
static modes.
Note: A different current value can be set for each
current range (High/Mid/Low).
Note: The [:VA] node can only be omitted when in
static mode.
Syntax
:CURRent[:VA] {<NRf>[ A ] | MINimum | MAXimum }
Query Syntax
:CURRent[:VA]?
Parameter
<NRf>[A]
“A Value” current value
MINIMUM or MIN
Minimum current level
MAXIMUM or MAX
Maximum current level
Return parameter
<NR2>
Returns the “A Value”
current value.
Example
:CURRent:VA MIN
Sets the current value to the minimum.
- DC Electronic Load 1
- Table of Contents 3
- INTERFACE OVERVIEW 4
- Front Panel Overview 5
- Rear Panel Overview 6
- Interface Configuration 7
- Configure GPIB Interface 8
- 1 2 3 4 5 9
- GPIB Function Check 15
- INTERFACE OVERVIEW 17
- COMMNAND OVERVIEW 18
- :CURRent:Set 21
- Command List 23
- :CURRent[:VA]:TRIGgered 37
- :RESistance[:VA]:TRIGgered 37
- Example 38
- :RESistance:TRIGgered MAX 38
- :INPut:MODE 40
- :MEASure:ETIMe? 42
- Configure Subsystem Commands 43
- [:CONFigure]:OCP 43
- [:CONFigure]:OPP 44
- [:CONFigure]:SSTart 46
- [:CONFigure]:COTime 49
- [:CONFigure]:GNG:C 55
- Parallel Commands 56
- [:CONFigure]:PARallel 56
- Step Resolution Commands 58
- [:CONFigure]:STEP:CCH 58
- [:CONFigure]:STEP:CC 60
- [:CONFigure]:STEP:CRH 60
- [:CONFigure]:STEP:CRM 61
- [:CONFigure]:STEP:CRL 62
- [:CONFigure]:STEP:CR 62
- [:CONFigure]:STEP:CV 64
- [:CONFigure]:STEP:CPH 64
- [:CONFigure]:STEP:CP 66
- [:MODE]:DYNamic 71
- Current Subsystem Commands 72
- :CURRent[:VA] 72
- :CURRent:SET 75
- :CURRent:T2 78
- :RESistance[:VA] 81
- :RESistance:L1 83
- :RESistance:LEVel 85
- :RESistance:T1 87
- :RESistance:DUTY 89
- Power Subsystem Commands 93
- :POWer[:VA] 93
- :POWer:LEVel 96
- :POWer:FREQuency 98
- :POWer:DUTY 99
- Function Commands 100
- :PROGram:STATe 101
- :PROGram 102
- :PROGram[:RECall]:DEFault 103
- :PROGram:STARt 103
- [:PROGram]:CHAin:P2P 109
- :PROGram:SAVE 110
- :NSEQuence:STATe 110
- :NSEQuence 111
- :NSEQuence:STARt 112
- :NSEQuence:EDIT 117
- :NSEQuence:EDIT:POINt 118
- :FSEQuence 120
- :FSEQuence:MEMO 121
- :FSEQuence:EDIT:POINt 126
- :FSEQuence:SAVE 128
- :UTILity:LOAD:MODE 130
- :UTILity:LOAD:RANGe 131
- SCPI Register Commands 142
- :SYSTem:ERRor? 142
- :STATus:PRESet 143
- :STATus:CSUMmary:PTRansition 151
- Status Registers 153
- CSummary Status Registers 155
- Questionable Status Register 156
- Operation Status Registers 157
- Status Byte Register 160
- Service Request Register 161
- Error Messages 162
Relacionado con productos y manuales para Equipo Gw-instek PEL-3000 Series Programming Manual
Equipo Gw-instek APS-1102 User Manual Manual de usuario
(265 paginas)
(265 paginas)
Equipo Gw-instek PCS-1000 Manual de usuario
(93 paginas)
(93 paginas)
Equipo Gw-instek GPD-4303S Manual de usuario
(59 paginas)
(59 paginas)
Equipo Gw-instek APS-1102A User Manual Manual de usuario
(285 paginas)
(285 paginas)
Equipo Gw-instek PPH-1503 Manual de usuario
(137 paginas)
(137 paginas)
Equipo Gw-instek LCR-914 Manual de usuario
(28 paginas)
(28 paginas)
Equipo Gw-instek LCR-800 Series Manual de usuario
(72 paginas)
(72 paginas)
Equipo Gw-instek GPM-8212 Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales